Gw-instek PEL-3000 Series Programming Manual Instrukcja Użytkownika Pobierz pdf (Strona 34)

PEL-3000 Programming Manual

*TST?

Set

Query

Description

This command is a standard SCPI self-test

command. The PEL-3000 does not perform any

self-tests so will always return 0 (pass) for this

command.

Query Syntax

*TST?

Return parameter

<NR1>

Pass

Query example

*TST?

*WAI

Set

Description

Wait command. Prevents new operations from

executing until all pending operations have

finished.

Syntax

*WAI

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 173 174

DC Electronic Load 1
Table of Contents 3
INTERFACE OVERVIEW 4
Front Panel Overview 5
Rear Panel Overview 6
Interface Configuration 7
Configure GPIB Interface 8
1 2 3 4 5 9
GPIB Function Check 15
INTERFACE OVERVIEW 17
COMMNAND OVERVIEW 18
:CURRent:Set 21
Command List 23
:CURRent[:VA]:TRIGgered 37
:RESistance[:VA]:TRIGgered 37
Example 38
:RESistance:TRIGgered MAX 38
:INPut:MODE 40
:MEASure:ETIMe? 42
Configure Subsystem Commands 43
[:CONFigure]:OCP 43
[:CONFigure]:OPP 44
[:CONFigure]:SSTart 46
[:CONFigure]:COTime 49
[:CONFigure]:GNG:C 55
Parallel Commands 56
[:CONFigure]:PARallel 56
Step Resolution Commands 58
[:CONFigure]:STEP:CCH 58
[:CONFigure]:STEP:CC 60
[:CONFigure]:STEP:CRH 60
[:CONFigure]:STEP:CRM 61
[:CONFigure]:STEP:CRL 62
[:CONFigure]:STEP:CR 62
[:CONFigure]:STEP:CV 64
[:CONFigure]:STEP:CPH 64
[:CONFigure]:STEP:CP 66
[:MODE]:DYNamic 71
Current Subsystem Commands 72
:CURRent[:VA] 72
:CURRent:SET 75
:CURRent:T2 78
:RESistance[:VA] 81
:RESistance:L1 83
:RESistance:LEVel 85
:RESistance:T1 87
:RESistance:DUTY 89
Power Subsystem Commands 93
:POWer[:VA] 93
:POWer:LEVel 96
:POWer:FREQuency 98
:POWer:DUTY 99
Function Commands 100
:PROGram:STATe 101
:PROGram 102
:PROGram[:RECall]:DEFault 103
:PROGram:STARt 103
[:PROGram]:CHAin:P2P 109
:PROGram:SAVE 110
:NSEQuence:STATe 110
:NSEQuence 111
:NSEQuence:STARt 112
:NSEQuence:EDIT 117
:NSEQuence:EDIT:POINt 118
:FSEQuence 120
:FSEQuence:MEMO 121
:FSEQuence:EDIT:POINt 126
:FSEQuence:SAVE 128
:UTILity:LOAD:MODE 130
:UTILity:LOAD:RANGe 131
SCPI Register Commands 142
:SYSTem:ERRor? 142
:STATus:PRESet 143
:STATus:CSUMmary:PTRansition 151
Status Registers 153
CSummary Status Registers 155
Questionable Status Register 156
Operation Status Registers 157
Status Byte Register 160
Service Request Register 161
Error Messages 162

Komentarze do niniejszej Instrukcji

Brak uwag

Gw-instek PEL-3000 Series Programming Manual Instrukcja Użytkownika Strona 34

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Ekwipunek Gw-instek PEL-3000 Series Programming Manual