Gw-instek APS-1102 Control Software User Manual Instrukcja Użytkownika Strona 79
- Strona / 134
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
8.3 Waveform Generation Through Interpolation
8-15
8.3.1 Control point setting
Interpolation is applied to the range selected by markers on the waveform display screen.
Although control points can be set outside the selected range, they will be ignored in the actual
interpolation.
a) Specifying the control point with a numerical value
Input numerical values in the input areas to the right of [X=] and [Y=] on the interpolation editing
screen.
To activate the input area to the right of [X=], click the input area or press Alt + X .
To activate the input area to the right of [Y=], click the input area or press Alt + Y .
Click the Add button to display a [+] mark at the specified position in the waveform display area.
Furthermore, the control point position is displayed with a numerical value in the control point
chart on the interpolation editing screen. The chart is arranged from the lowest to highest X
values.
b) Specifying the control point with mouse
If any of control points’ [+] marks are shown in red (selected), click an unmarked location of the
waveform display area to change all marks to light blue (deselected).
Move the mouse cursor to a desired location for adding a control point and click while holding
down the
Ctrl key to add a control point. The newly added control point will be in the selected
status and displayed in red.
c) Moving the interpolation control point with a numerical value
When one of the control points listed on the interpolation editing screen is clicked, the clicked
control point is selected and the following processing is performed.
The specified portion of the chart is highlighted.
The input areas to the right of [X
=] and [Y=] displays the position of the selected control point.
The corresponding [+] mark on the waveform display screen is displayed in red.
The control point can be selected by clicking the [+] mark on the waveform display screen. If the
screen magnification ratio is low, it might be difficult to capture the mark due to the display
resolution.
With the control point selected, update the numerical values in the input areas to the right of [X
=]
and [Y
=] input area and click the Add button to move the selected control point.
d) Moving the control point with mouse
The control point can be moved by dragging the [+] mark on the waveform display screen. If the
screen magnification ratio is low, it might be difficult to capture the mark due to the display
resolution.
e) Deleting the control point
Click the
Delete button to delete the selected control point.
The selected control point cannot be restored. Take care when using this function.
- APS-1102 1
- CONTROL SOFTWARE USER MANUAL 1
- Preface 3
- Safety Precautions 4
- Disclaimer 5
- Contents 6
- Figures and Tables 10
- OVERVIEW 13
- 1.1 General 14
- 1.2 Organization of Product 14
- 1.3 Software Configuration 15
- 1.4 Online/Offline 15
- 1.5 Conventions 15
- INSTALLATION 17
- 2.1 Hardware Requirements 18
- 2.2 Installation Procedure 19
- LAUNCHER 21
- 3.1 Starting the Launcher 22
- 3.3 Exiting the Launcher 23
- 3.4 Notes 23
- REMOTE CONTROL 25
- 4.1 Component Names 26
- 4.1.2 Toolbar 27
- 4.1.3 Status bar 27
- 4.2 Menu Organization 28
- 4.3 Start 28
- 4.4 Exit 29
- 4.5.2 Oscillator settings 30
- 4.5.3 Miscellaneous settings 30
- 4.5.4 Output setting 31
- 4.6 Device Setting File 32
- 4.7 Memory 33
- 4.8 Status Display 34
- 4.9 System Setup 35
- 4.10 Errors 36
- LOGGING 37
- 5.1 Component Names 38
- 5.2 Menu Organization 39
- 5.3 Start and Termination 40
- 5.5 Data Display Area 40
- 5.6 Logging Conditions 41
- 5.7 Logging Data File 41
- 5.8 Logging Data 42
- CREATION 43
- 6.1 General 44
- 6.2 Start and Termination 45
- 6.3 Standard Waveform 45
- key 48
- button 48
- Enter key 49
- button 50
- WAVEFORM DISPLAY SCREEN 53
- 7.2 Tool Menu 56
- 7.3 Setting Menu 56
- 7.4 Undo and Redo 56
- 7.5.1 Vertical zoom 57
- 7.5.2 Horizontal zoom 57
- 7.5.3 Scrolling 57
- 7.5.5 Marker operations 58
- 7.5.6 Range selection 59
- 7.6.1 File types 60
- 7.6.2 New 60
- 7.6.4 Text file 61
- 7.6.5 Import 62
- 7.7 Copy and Paste 63
- OPERATIONS 65
- Expression Waveform 66
- 8.1.2 Waveform selection 67
- 8.1.3 Parameter setting 68
- Cancel button at 69
- key 69
- + - ! 71
- * / 71
- + - 71
- == != 71
- [Y=] in the “ARB” 72
- 1 ms is regarded as 2 72
- 8.1.5 File operation 74
- 8.1.6 Print 74
- ( Alt , T 75
- OK button 76
- 8.3.1 Control point setting 79
- 8.3.2 Interpolation 80
- 8.3.3 File operation 80
- 8.4.1 Operation types 81
- 8.4.2 Object of operation 81
- 8.4.3 Operation execution 82
- 8.5.1 Model setting 84
- (ACDC-INT, ACDC-ADD only) 85
- 8.5.4 Transferring data 86
- 8.5.5 Horizontal axis unit 87
- 8.5.6 Vertical axis unit 88
- 8.5.7 File operations 88
- 8.5.8 Print 89
- SEQUENCE EDITING 91
- 9.1 Component Names 92
- 9.2 Menu Organization 93
- 9.3 Start and Termination 94
- 9.4 Sequence Edit Area 95
- Add button 96
- Move button 96
- 9.4.2 Setting parameters 97
- 9.6 Sequence Control Buttons 102
- Branch button with a branch 103
- 9.8 Message Display Area 105
- SEQUENCE VIEW WINDOW 107
- 10.1 Sequence View Window 108
- 10.2 Sequence Preview 110
- 10.2.3 Sequence Display Area 111
- 10.5 Message Display Area 113
- OTHER SCREEN OPERATIONS FOR 115
- 11.1 Vertical Tiling 116
- 11.2 Offline Mode 117
- Figure 11-2” 118
- User Manual 118
- Caution 118
- 11.6 Mode Setting 120
- 11.7 System Settings 121
- ERROR MESSAGES 125
- 12.1 Launcher Errors 126
- MAINTENANCE 131
- 13.1 Handling CD-ROM 132
- 13.3 Version Check 132
- IMPORTANT 133
Powiązane produkty i podręczniki dla Ekwipunek Gw-instek APS-1102 Control Software User Manual
Ekwipunek Gw-instek PPH-1503 Instrukcja Użytkownika
(137 strony)
(137 strony)
PSC PowerScan RF manuels
Manuels d'utilisation et guides de l'utilisateur pour Scanners PSC PowerScan RF.
Nous fournissons des manuels en pdf 1 PSC PowerScan RF à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji